Aijiren Lab LC Series Multisamplers User Manual 12 Product Description ( ) The Aijiren II Multisampler can handle both vials and microtiter plates with ease and efficiency up to 1300 bar system pressure, optimized on chromatographic performance. In fact, this compact module has the capacity to house up to 6144 samples
Aijiren Lab Advisor Software 77 Aijiren Standard Autosampler User Manual 11 ... be combined with the Aijiren Thermostat ( ). ...
Glass Vials Lab 8-425 neck finish represents a hplc vials &gc vials the vials a diameter of 8 mm across the outside of the threads and a thread style of 425, Vials has clear and amber, Screw Cap in Lab most of the 2ml vials are 12*32mm Autosampler Hplc Vials &gc vials are available in a variety of neck finishes and opening diameters.
Replace Needle – Aijiren Autosampler 1. Turn the needle carrier 90° clockwise. 4. 2. Flip the leak guide open. and remove the loop capillary from the 3. Hold the needle assembly in position and needle assembly. loosen the loop fitting capillary. 6. Pinch the holder clamp, pull back 5. Push the silicon safety tube over the needle.
Glass Vials Lab 8-425 neck finish represents a hplc vials &gc vials the vials a diameter of 8 mm across the outside of the threads and a thread style of 425, Vials has clear and amber, Screw Cap in Lab most of the 2ml vials are 12*32mm Autosampler Hplc Vials &gc vials are available in a variety of neck finishes and opening diameters.
The II Vialsampler combines sample management and column handling in a single autosampler module. The Vialsampler injects from up to 132 standard 2 mL vials and has a pressure rating of 600 or 800 bar. Options and upgrades are available for sample cooling and heating from 4 to 40 °C.
End the connection from Lab Advisor, and close Lab Advisor. Open your CDS software and run the HPLC with normal flow rates. Make sure to work in mainpass mode. If the pressure is still high after the backflush, you will need a new seat. If you need more help, contact your local Aijiren Technologies Support representative.
1 Injection valve rotor seal. 1Open the front door.2Remove all capillaries from the Injection valve with a 1/4 inch wrench. Aijiren Autosampler User Manual 147 Maintenance9. Replacing the Rotor seal 3Unscrew and remove the three stator screws from the stator head with a 9/64 inch hex key.
Our standard 2 mL vial is 12 mm in diameter, 32 mm in height, and has a 4.6 mm opening. The main application for HPLC, autosampler, chromatography, Aijiren, waters machine. All autosamplers of Ajiren Tech are 100% integrity tested and manufactured according to ISO 9001 standard. If a 2ml screw HPLC vialsis required.
Aijiren Technologies Series HPLC Standard Operating • Load samples into labeled HPLC vials (VWR cat # may be used). Each vial holds a maximum of 1.5 mL but do not need to be completely filled; because the autosampler needle collects sample from the bottom of the vial, only ≈0.5 mL is necessary.
Aijiren Restricted September 10, 2008Month ##, 200X Page 14 Split Peaks from Injection Solvent Effects Column: StableBond SB-C8, 4.6 x 150 mm, 5 μm Mobile Phase: 82% H 2O : 18% ACN Injection Volume: 30 μL Sample: 1. Caffeine 2. Salicylamide A. Injection Solvent 100% Acetonitrile B. Injection Solvent Mobile Phase
2ml Lab Glass Vials for Aijiren Autosampler. Screw-top vials also come in different sizes, with vial caps made of either aluminum for crimp seals or plastic. Amber glass vials are available in 2ml volume with a screw top. Inserts work in conjunction with any autosampler and fit either standard or wide openings vials. Rated 5 /5 based on 371
Aijiren Technologies Series HPLC Standard Operating. • Load samples into labeled HPLC vials (VWR cat # may be used). Each vial holds a maximum of 1.5 mL but do not need to be completely filled; because the autosampler needle collects sample from the bottom of the vial, only ≈0.5 mL is necessary.
Home » News » 2ml hplc lab vials » Standard Opening hplc 2 ml lab vials for sale Aijiren Standard Opening hplc 2 ml lab vials for sale Aijiren Material: USP Type 1, Class A, 33 Borosilicate Glass Volume: 2ml (standard volume) 1.5ml(actual volume) Application: HPLC and GC system Dimensions: 11.6 x 32mm Neck Diameter: 9mm Qty/Pack: 100pcs/pack Payment: T/T MOQ: 1pack
The Autosampler features an increased pressure range enabling the use of today’s column technology (sub- two- micron narrow bore columns) with the Aijiren LC System. Increased robustness is achieved by optimized new parts, high speed with lowest carry- over by flow through design, increased sample injection speed